Search tips
Search criteria

Results 1-25 (1129093)

Clipboard (0)

Related Articles

1.  Assessment of bone ingrowth potential of biomimetic hydroxyapatite and brushite coated porous E-beam structures 
The bone ingrowth potential of biomimetic hydroxyapatite and brushite coatings applied on porous E-beam structure was examined in goats and compared to a similar uncoated porous structure and a conventional titanium plasma spray coating. Specimens were implanted in the iliac crest of goats for a period of 3 (4 goats) or 15 weeks (8 goats). Mechanical implant fixation generated by bone ingrowth was analyzed by a push out test. Histomorphometry was performed to assess the bone ingrowth depth and bone implant contact. The uncoated and hydroxyapatite-coated cubic structure had significantly higher mechanical strength at the interface compared to the Ti plasma spray coating at 15 weeks of implantation. Bone ingrowth depth was significantly larger for the hydroxyapatite- and brushite-coated structures compared to the uncoated structure. In conclusion, the porous E-beam surface structure showed higher bone ingrowth potential compared to a conventional implant surface after 15 weeks of implantation. Addition of a calcium phosphate coating to the E-beam structure enhanced bone ingrowth significantly. Furthermore, the calcium phosphate coating appears to work as an accelerator for bone ingrowth.
PMCID: PMC3085057  PMID: 21327405
2.  Evaluation of Biological Properties of Electron Beam Melted Ti6Al4V Implant with Biomimetic Coating In Vitro and In Vivo 
PLoS ONE  2012;7(12):e52049.
High strength porous titanium implants are widely used for the reconstruction of craniofacial defects because of their similar mechanical properties to those of bone. The recent introduction of electron beam melting (EBM) technique allows a direct digitally enabled fabrication of patient specific porous titanium implants, whereas both their in vitro and in vivo biological performance need further investigation.
In the present study, we fabricated porous Ti6Al4V implants with controlled porous structure by EBM process, analyzed their mechanical properties, and conducted the surface modification with biomimetic approach. The bioactivities of EBM porous titanium in vitro and in vivo were evaluated between implants with and without biomimetic apatite coating.
The physical property of the porous implants, containing the compressive strength being 163 - 286 MPa and the Young’s modulus being 14.5–38.5 GPa, is similar to cortical bone. The in vitro culture of osteoblasts on the porous Ti6Al4V implants has shown a favorable circumstance for cell attachment and proliferation as well as cell morphology and spreading, which were comparable with the implants coating with bone-like apatite. In vivo, histological analysis has obtained a rapid ingrowth of bone tissue from calvarial margins toward the center of bone defect in 12 weeks. We observed similar increasing rate of bone ingrowth and percentage of bone formation within coated and uncoated implants, all of which achieved a successful bridging of the defect in 12 weeks after the implantation.
This study demonstrated that the EBM porous Ti6Al4V implant not only reduced the stress-shielding but also exerted appropriate osteoconductive properties, as well as the apatite coated group. The results opened up the possibility of using purely porous titanium alloy scaffolds to reconstruct specific bone defects in the maxillofacial and orthopedic fields.
PMCID: PMC3525565  PMID: 23272208
3.  Removing Biofilms from Microstructured Titanium Ex Vivo: A Novel Approach Using Atmospheric Plasma Technology 
PLoS ONE  2011;6(10):e25893.
The removal of biofilms from microstructured titanium used for dental implants is a still unresolved challenge. This experimental study investigated disinfection and removal of in situ formed biofilms from microstructured titanium using cold atmospheric plasma in combination with air/water spray. Titanium discs (roughness (Ra): 1.96 µm) were exposed to human oral cavities for 24 and 72 hours (n = 149 each) to produce biofilms. Biofilm thickness was determined using confocal laser scanning microscopy (n = 5 each). Plasma treatment of biofilms was carried out ex vivo using a microwave-driven pulsed plasma source working at temperatures from 39 to 43°C. Following plasma treatment, one group was air/water spray treated before re-treatment by second plasma pulses. Vital microorganisms on the titanium surfaces were identified by contact culture (Rodac agar plates). Biofilm presence and bacterial viability were quantified by fluorescence microscopy. Morphology of titanium surfaces and attached biofilms was visualized by scanning electron microscopy (SEM). Total protein amounts of biofilms were colorimetrically quantified. Untreated and air/water treated biofilms served as controls. Cold plasma treatment of native biofilms with a mean thickness of 19 µm (24 h) to 91 µm (72 h) covering the microstructure of the titanium surface caused inactivation of biofilm bacteria and significant reduction of protein amounts. Total removal of biofilms, however, required additional application of air/water spray, and a second series of plasma treatment. Importantly, the microstructure of the titanium discs was not altered by plasma treatment. The combination of atmospheric plasma and non-abrasive air/water spray is applicable for complete elimination of oral biofilms from microstructured titanium used for dental implants and may enable new routes for the therapy of periimplant disease.
PMCID: PMC3189945  PMID: 22016784
4.  Bone integration capability of nanopolymorphic crystalline hydroxyapatite coated on titanium implants 
The mechanism by which hydroxyapatite (HA)-coated titanium promotes bone–implant integration is largely unknown. Furthermore, refining the fabrication of nano-structured HA to the level applicable to the mass production process for titanium implants is challenging. This study reports successful creation of nanopolymorphic crystalline HA on microroughened titanium surfaces using a combination of flame spray and low-temperature calcination and tests its biological capability to enhance bone–implant integration. Sandblasted microroughened titanium implants and sandblasted + HA-coated titanium implants were subjected to biomechanical and histomorphometric analyses in a rat model. The HA was 55% crystallized and consisted of nanoscale needle-like architectures developed in various diameters, lengths, and orientations, which resulted in a 70% increase in surface area compared to noncoated microroughened surfaces. The HA was free from impurity contaminants, with a calcium/phosphorus ratio of 1.66 being equivalent to that of stoichiometric HA. As compared to microroughened implants, HA-coated implants increased the strength of bone–implant integration consistently at both early and late stages of healing. HA-coated implants showed an increased percentage of bone–implant contact and bone volume within 50 μm proximity of the implant surface, as well as a remarkably reduced percentage of soft tissue intervention between bone and the implant surface. In contrast, bone volume outside the 50 μm border was lower around HA-coated implants. Thus, this study demonstrated that the addition of pure nanopolymorphic crystalline HA to microroughened titanium not only accelerates but also enhances the level of bone–implant integration and identified the specific tissue morphogenesis parameters modulated by HA coating. In particular, the nanocrystalline HA was proven to be drastic in increasing osteoconductivity and inhibiting soft tissue infiltration, but the effect was limited to the immediate microenvironment surrounding the implant.
PMCID: PMC3284227  PMID: 22359461
osseointegration; dental and orthopedic implant; nanotechnology; bone–implant integration; HA; calcium phosphate
5.  Biomechanical and Histological Evaluation of Roughened Surface Titanium Screws Fabricated by Electron Beam Melting 
PLoS ONE  2014;9(4):e96179.
Various fabrication methods are used to improve the stability and osseointegration of screws within the host bone. The aim of this study was to investigate whether roughened surface titanium screws fabricated by electron beam melting can provide better stability and osseointegration as compared with smooth titanium screws in sheep cervical vertebrae.
Roughened surface titanium screws, fabricated by electron beam melting, and conventional smooth surface titanium screws were implanted into sheep for 6 or 12 weeks (groups A and B, respectively). Bone ingrowth and implant stability were assessed with three-dimensional imaging and reconstruction, as well as histological and biomechanical tests.
No screws in either group showed signs of loosening. Fibrous tissue formation could be seen around the screws at 6 weeks, which was replaced with bone at 12 weeks. Bone volume/total volume, bone surface area/bone volume, and the trabecular number were significantly higher for a define region of interest surrounding the roughened screws than that surrounding the smooth screws at 12 weeks. Indeed, for roughened screws, trabecular number was significantly higher at 12 weeks than at 6 weeks. On mechanical testing, the maximum pullout strength was significantly higher at 12 weeks than at 6 weeks, as expected; however, no significant differences were found between smooth and roughened screws at either time point. The maximum torque to extract the roughened screws was higher than that required for the smooth screws.
Electron beam melting is a simple and effective method for producing a roughened surface on titanium screws. After 12 weeks, roughened titanium screws demonstrated a high degree of osseointegration and increased torsional resistance to extraction over smooth titanium screws.
PMCID: PMC4005762  PMID: 24788866
6.  Cancellous Bone Osseointegration Is Enhanced by In Vivo Loading 
Tissue Engineering. Part C, Methods  2010;16(6):1399-1406.
Biophysical stimuli may be an effective therapy to counteract age-related changes in bone structure that affect the primary stability of implants used in joint replacement or fracture fixation. The influence of controlled mechanical loading on osseointegration was investigated using an in vivo device implanted in the distal lateral femur of 12 male rabbits. Compressive loads (1 MPa, 1 Hz, 50 cycles/day, 4 weeks) were applied to a porous titanium foam implant and the underlying cancellous bone. The contralateral limbs served as nonloaded controls. Backscattered electron imaging indicated that the amount of bone ingrowth was significantly greater in the loaded limb than in the nonloaded control limb, whereas the amount of underlying cancellous periprosthetic bone was similar. No significant difference in the mineral apposition rate of the bone ingrowth or periprosthetic bone was measured in the loaded compared to the control limb. Histological analysis demonstrated newly formed woven bone in direct apposition to the implant coating, with a lack of fibrous tissue at the implant–periprosthetic bone interface in both loaded and nonloaded implants. The lack of fibrous tissue demonstrates that mechanical stimulation using this model significantly enhanced cancellous bone ingrowth without the detrimental effects of micromotion. These results suggest that biophysical therapy should be further investigated to augment current treatments to enhance long-term fixation of orthopedic devices. Additionally, this novel in vivo loading model can be used to further investigate the influence of biophysical stimulation on other tissue engineering approaches requiring bone ingrowth into both metallic and nonmetallic cell-seeded scaffolds.
PMCID: PMC2988627  PMID: 20367497
7.  Ag-plasma modification enhances bone apposition around titanium dental implants: an animal study in Labrador dogs 
Dental implants with proper antibacterial ability as well as ideal osseointegration are being actively pursued. The antimicrobial ability of titanium implants can be significantly enhanced via modification with silver nanoparticles (Ag NPs). However, the high mobility of Ag NPs results in their potential cytotoxicity. The silver plasma immersion ion-implantation (Ag-PIII) technique may remedy the defect. Accordingly, Ag-PIII technique was employed in this study in an attempt to reduce the mobility of Ag NPs and enhance osseointegration of sandblasted and acid-etched (SLA) dental implants. Briefly, 48 dental implants, divided equally into one control and three test groups (further treated by Ag-PIII technique with three different implantation parameters), were inserted in the mandibles of six Labrador dogs. Scanning electron microscopy, X-ray photoelectron spectroscopy, and inductively coupled plasma optical emission spectrometry were used to investigate the surface topography, chemical states, and silver release of SLA- and Ag-PIII-treated titanium dental implants. The implant stability quotient examination, Microcomputed tomography evaluation, histological observations, and histomorphometric analysis were performed to assess the osseointegration effect in vivo. The results demonstrated that normal soft tissue healing around dental implants was observed in all the groups, whereas the implant stability quotient values in Ag-PIII groups were higher than that in the SLA group. In addition, all the Ag-PIII groups, compared to the SLA-group, exhibited enhanced new bone formation, bone mineral density, and trabecular pattern. With regard to osteogenic indicators, the implants treated with Ag-PIII for 30 minutes and 60 minutes, with the diameter of the Ag NPs ranging from 5–25 nm, were better than those treated with Ag-PIII for 90 minutes, with the Ag NPs diameter out of that range. These results suggest that Ag-PIII technique can reduce the mobility of Ag NPs and enhance the osseointegration of SLA surfaces and have the potential for future use.
PMCID: PMC4298332  PMID: 25609967
surface modification; micro/nanostructure; silver; ion implantation; osseointegration
8.  Osseointegration in arthroplasty: can simvastatin promote bone response to implants? 
International Orthopaedics  2007;33(3):855-859.
Cementless fixation depends on bone ingrowth for long-term success. Simvastatin as a lipid lowering agent has been demonstrated to have osteoanabolic effects. This study was designed to measure the possible effect of simvastatin on implant osseointegration. Bilateral femoral implantation of titanium cylinders was performed in 20 rabbits. Blood lipid levels were measured pre- and postoperatively. Scanning electron microscopy (SEM) was used to measure the percentage of the surface of each implant in contact with bone and mechanical pull-out testing was performed. The blood lipid levels were significantly reduced in the simvastatin group. Histomorphometric examination revealed increased bone ingrowth and mechanical examination showed increased interface strength in the simvastatin group. Mechanical and histological data showed superior stability and osseous adaptation at the bone/implant interface for the simvastatin group. We conclude that simvastatin has potential as a means of enhancing bone ingrowth, which is a key factor in the longevity of cementless implants.
PMCID: PMC2903108  PMID: 18157535
9.  Osteogenic Protein-1 for Long Bone Nonunion 
Executive Summary
To assess the efficacy of osteogenic protein-1 (OP-1) for long bone nonunion.
Clinical Need
Although most fractures heal within a normal period, about 5% to 10% do not heal and are classified as delayed or nonunion fractures. Nonunion and segmental bone loss after fracture, reconstructive surgery, or lesion excision can present complex orthopedic problems, and the multiple surgical procedures often needed are associated with patient morbidity and reduced quality of life.
Many factors contribute to the pathogenesis of a delayed union or nonunion fractures, including deficiencies of calcium, vitamin D, or vitamin C, and side effects of medications such as anticoagulants, steroids, some anti-inflammatory drugs, and radiation. It has been shown that smoking interferes with bone repair in several ways.
Incidence of Nonunion and Delayed Union Cases
An estimated 5% to 10% of fractures do not heal properly and go on to delayed union or nonunion. If this overall estimate of incidence were applied to the Ontario population1, the estimated number of delayed union or nonunion in the province would be between 3,863 and 7,725.
Treatment of Nonunion Cases
The treatment of nonunion cases is a challenge to orthopedic surgeons. However, the basic principle behind treatment is to provide both mechanical and biological support to the nonunion site.
Fracture stabilization and immobilization is frequently used with the other treatment modalities that provide biological support to the fractured bone. Biological support includes materials that could be served as a source of osteogenic cells (osteogenesis), a stimulator of mesenchymal cells (osteoinduction), or a scaffold-like structure (osteoconduction).
The capacity to heal a fracture is a latent potential of the stromal stem cells, which synthesize new bone. This process has been defined as osteogenesis. Activation of the stem cells to initiate osteogenic response and to differentiate into bone-forming osteoblasts is called osteoinduction. These 2 properties accelerate the rate of fracture healing or reactivate the ineffective healing process. Osteoconduction occurs when passive structures facilitate the migration of osteoprogenitor cells, the perivascular tissue, and capillaries into these structures.
Bone Grafts and Bone Graft Substitutes
Bone graft and bone graft substitutes have one or more of the following components:
Undifferentiated stem cells
Growth factors
Structural lattice
Undifferentiated stem cells are unspecialized, multipotential cells that can differentiate into a variety of specialized cells. They can also replicate themselves. The role of stem cells is to maintain and repair the tissue in which they are residing. A single stem cell can generate all cell types of that tissue. Bone marrow is a source of at least 2 kinds of stem cells. Hematopoietic stem cells that form all types of blood cells, and bone marrow stromal stem cells that have osteogenic properties and can generate bone, cartilage, and fibrous tissue.
Bone marrow has been used to stimulate bone formation in bone defects and cases of nonunion fractures. Bone marrow can be aspirated from the iliac crest and injected percutaneously with fluoroscopic guidance into the site of the nonunion fracture. The effectiveness of this technique depends on the number and activity of stem cells in the aspirated bone marrow. It may be possible to increase the proliferation and speed differentiation of stem cells by exposing them to growth factor or by combining them with collagen.
Many growth factors and cytokines induced in response to injury are believed to have a considerable role in the process of repair. Of the many bone growth factors studied, bone morphogenetics (BMPs) have generated the greatest attention because of their osteoinductive potential. The BMPs that have been most widely studied for their ability to induce bone regeneration in humans include BMP-2 and BMP-7 (osteogenic protein). Human osteogenic protein-1 (OP-1) has been cloned and produced with recombinant technology and is free from the risk of infection or allergic reaction.
The structural lattice is osteoconductive; it supports the ingrowth of developing capillaries and perivascular tissues. Three distinct groups of structural lattice have been identified: collagen, calcium sulphate, and calcium phosphate. These materials can be used to replace a lost segment of bone.
Grafts Used for Nonunion
Autologous bone graft is generally considered the gold standard and the best material for grafting because it contains several elements that are critical in promoting bone formation, including osteoprogenitor cells, the matrix, and bone morphogenetic proteins. The osteoconductive property of cancellous autograft is related to the porosity of bone. The highly porous, scaffold-like structure of the graft allows host osteoblasts and host osteoprogenitor cells to migrate easily into the area of the defect and to begin regeneration of bone. Sources of cancellous bone are the iliac crest, the distal femur, the greater trochanter, and the proximal tibia. However, harvesting the autologous bone graft is associated with postoperative pain at the donor site, potential injury to the surrounding arteries, nerves, and tissues, and the risk of infection. Thus the development of synthetic materials with osteoconductive and osteoinductive properties that can eliminate the need for harvesting has become a major goal of orthopedic research.
Allograft is the graft of tissue between individuals who are of the same species but are of a disparate genotype. Allograft has osteoconductive and limited osteoinductive properties. Demineralized bone matrix (DBM) is human cortical and cancellous allograft. These products are prepared by acid extraction of allograft bone, resulting in the loss of most of the mineralized component while collagen and noncollagenous proteins, including growth factors, are retained. Figures 1 to 5 demonstrate the osteogenic, osteoinduction, and osteoconduction properties of autologous bone graft, allograft, OP-1, bone graft substitutes, and bone marrow.
Autologous Bone Graft
Osteogenic Protein-1
Allograft bone and Demineralized Bone Matrix
Bone Graft Substitutes
Autologous Bone Marrow Graft
New Technology Being Reviewed: Osteogenic Protein-1
Health Canada issued a Class IV licence for OP-1 in June 2004 (licence number 36320). The manufacturer of OP-1 is Stryker Biotech (Hapkinton, MA).
The United States Food and Drug Administration (FDA) issued a humanitarian device exemption for the application of the OP-1 implant as an “alternative to autograft in recalcitrant long bone nonunions where use of autograft is unfeasible and alternative treatments have failed.” Regulatory agencies in Europe, Australia, and New Zealand have permitted the use of this implant in specific cases, such as in tibial nonunions, or in more general cases, such as in long bone nonunions.
According to the manufacturer, OP-1 is indicated for the treatment of long bone nonunions. It is contraindicated in the patient has a hypersensitivity to the active substance or collagen, and it should not be applied at the site of a resected tumour that is at or near the defect or fracture. Finally, it should not be used in patients who are skeletally immature (< 18 years of age), or if there is no radiological evidence of closure of epiphysis.
Review Strategy
To summarize the safety profile and effectiveness of OP-1 in the treatment of cases of long bone nonunion and bone defects
To compare the effectiveness and cost effectiveness of OP-1 in the treatment of long bone nonunions and bone defects with the alternative technologies, particularly the gold standard autologous bone graft.
Literature Search
International Network of Agencies for Health Technology Assessments (INAHTA), the Cochrane Database of Systematic Reviews and the CCTR (formerly Cochrane Controlled Trials Register) were searched for health technology assessments. MEDLINE, EMBASE, Medline In Process and Other Non-Indexed Citations were searched from January 1, 1996 to January 27, 2004 for studies on OP-1. The search was limited to English-language articles and human studies. The search yielded 47 citations. Three studies met inclusion criteria (2 RCTs and 1 Ontario-based study presented at an international conference.
Summary of Findings
Friedlaender et al. conducted a prospective, randomized, partially blinded clinical trial on the treatment tibial nonunions with OP-1. Tibial nonunions were chosen for this study because of their high frequency, challenging treatment requirements, and substantial morbidity. All of the nonunions were at least 9 months old and had shown no progress toward healing over the previous 3 months. The patients were randomized to receive either treatment with autologous bone grafting or treatment with OP-1 in a type-1 collagen carrier. Both groups received reduction and fixation with an intramedullary rod. Table 1 summarizes the clinical outcomes of this study.
Outcomes in a Randomized Clinical Trial on Tibial Nonunions: Osteogenic Protein-1 versus Autologous Bone Grafting
Clinical success was defined as full weight-bearing, loss of severe pain at the fracture site on weight-bearing, and no further surgical treatment to enhance fracture repair.
The results of this study demonstrated that recombinant OP-1 is associated with substantial clinical and radiographic success for the treatment of tibial nonunions when used with intramedullary rod fixation. No adverse event related to sensitization was reported. Five per cent of the patients in the OP-1 group had circulating antibodies against type 1 collagen. Only 10% of the patients had a low level of anti-OP-1 antibodies, and all effects were transient. Furthermore, the success rate with the OP-1 implant was comparable with those achieved with autograft at 9 and 24 months follow-up. Eighty-two per cent of patients were successful at 24 months follow-up in both groups.
Statistically significant increased blood loss in the group treated with the autograft was observed (P = .049). Patients treated with autograft had longer operation and hospitalization times. All patients in the autograft group had pain at the donor site after surgery, and more than 80% judged their postoperative pain as moderate or severe. At their 6-month visit, 20% of the patients in the autograft group had persistent pain, mild or moderate in nature, at the donor site. This number fell to 13% at 12 months.
All patients in each of the groups had at least 1 adverse event that wasn’t serious, such as fever, nausea and vomiting, leg edema, discomfort, and bruising at the operative site. The incidence of these events was similar in both groups. Serious adverse events were observed in 44% of both groups, none of which were considered related to the OP-1 implant or autograft.
On the basis of this data, the FDA issued a humanitarian device exemption for the application of OP-1 implant as an alternative to autograft in recalcitrant long bone nonunions when the use of autograft is unfeasible and alternative treatments have failed.
Study on Fibular Defects
Geesink et al. investigated the osteogenic activity of OP-1 by assessing its value in bridging fibular defects made at the time of tibial osteotomy for varus or valgus deformity of the knee. This study had 2 phases and included 12 patients in each phase. Each phase included 12 patients (6 in each group). Patients in the first phase received either DBM or were left untreated. Patients in the second phase received either OP-1 on collagen type-1 or collagen type-1 alone.
Radiological and Dual Energy X-ray Absorptiometry (DEXA) evaluation showed that in patients in whom the defect was left untreated, no formation of bone occurred. At 12 months follow-up, new bone formation with bridging occurred in 4 of the 6 patients in DMB group, and 5 of the 6 patients in OP-1 group. One patient in OP-1 group did not show any evidence of new bone formation at any point during the study.
Ontario Pilot Study
A prospective pilot study was conducted in Ontario, Canada to investigate the safety and efficacy of OP-1 for the treatment of recalcitrant long bone nonunions. The study looked at 15 patients with complex, recalcitrant, long bone nonunions whose previous treatment had failed. The investigators concluded that this bone graft substitute appears to be safe and effective in providing sufficient biological stimulation in difficult to treat nonunions. Results of a more complete study on 70 patients are ready for publication. According to the principal investigator, OP-1 was 90% effective in inducing bone formation and bone healing in this sample.
Alternative Technologies
The Medical Advisory Secretariat conducted a literature search from January 1, 2000 to February 28, 2005 to identify studies on nonunions/bone defects that had been treated with alternative technologies. A review of these studies showed that, in addition to the gold standard autologous bone marrow grafting, bone allografts, demineralized bone matrices, bone graft substitutes, and autologous bone marrow have been used for treatment of nonunions and bone defects. These studies were categorized according to the osteoinductive, osteoconductive, and osteogenesis properties of the technologies studied.
A review of these studies showed that bone allografts have been used mostly in various reconstruction procedures to restore the defect after excavating a bone lesion. Two studies investigated the effectiveness of DBM in healing fracture nonunions. Calcium phosphate and calcium sulphate have been used mostly for repair of bone defects.
Several investigators have looked at the use of autologous bone marrow for treatment of long bone nonunions. The results of these studies show that method of percutaneous bone marrow grafting is highly effective in the treatment of long bone nonunions. In a total of 301 fractures across all studies, 268 (89%) healed with a mean healing time of 2.5 to 8 months. This healing time as derived from these case series is less than the timing of the primary end point in Friedlaender’s study (9 months). Table 2 summarizes the results of these studies. Table 2 summarizes the results of these studies.
Studies that used Percutaneous Bone Marrow Grafting for Treatment of Nonunions
Economic Analysis
Based on annual estimated incidence of long-bone nonunion of 3,863 - 7,725, the annual hospitalization costs associated with this condition is between $21.2 and $42.3 million based on a unit cost of $5,477 per hospital separation. When utilized, the device, a single vial of OP-1, is approximately $5,000 and if adopted universally in Ontario, the total device costs would be in the range of $19.3 - $38.6 million annually. The physician fee for harvest, insertion of bone, or OP-1 is $193 and is $193 for autologous bone marrow transplantation. Total annual physician costs are expected to be in the range of from $0.7 million to $1.3 million per year. Expenditures associated with long-bone nonunion are unlikely to increase since incidence of long-bone nonunion is unlikely to change in the future. However, the rate of uptake of OP-1 could have a significant impact on costs if the uptake were large.
The use of OP-1 and autologous bone marrow transplantation may offset pain medication costs compared with those associated with autologous bone harvest given that the former procedures do not involve the pain associated with the bone harvest site. However, given that this pain is normally not permanent, the overall offset is likely to be small. There are likely to be smaller OHIP costs associated with OP-1 than bone-harvest procedures given that only 1, rather than 2, incisions are needed when comparing the former with the latter procedure. This offset could amount to between $0.3 million to $0.7 million annually.
No data on the cost-effectiveness of OP-1 is available.
PMCID: PMC3382627  PMID: 23074475
10.  Osseointegration of zirconia implants compared with titanium: an in vivo study 
Head & Face Medicine  2008;4:30.
Titanium and titanium alloys are widely used for fabrication of dental implants. Since the material composition and the surface topography of a biomaterial play a fundamental role in osseointegration, various chemical and physical surface modifications have been developed to improve osseous healing. Zirconia-based implants were introduced into dental implantology as an altenative to titanium implants. Zirconia seems to be a suitable implant material because of its tooth-like colour, its mechanical properties and its biocompatibility. As the osseointegration of zirconia implants has not been extensively investigated, the aim of this study was to compare the osseous healing of zirconia implants with titanium implants which have a roughened surface but otherwise similar implant geometries.
Forty-eight zirconia and titanium implants were introduced into the tibia of 12 minipigs. After 1, 4 or 12 weeks, animals were sacrificed and specimens containing the implants were examined in terms of histological and ultrastructural techniques.
Histological results showed direct bone contact on the zirconia and titanium surfaces. Bone implant contact as measured by histomorphometry was slightly better on titanium than on zirconia surfaces. However, a statistically significant difference between the two groups was not observed.
The results demonstrated that zirconia implants with modified surfaces result in an osseointegration which is comparable with that of titanium implants.
PMCID: PMC2614983  PMID: 19077228
11.  Reality of Dental Implant Surface Modification: A Short Literature Review 
Screw-shaped endosseous implants that have a turned surface of commercially pure titanium have a disadvantage of requiring a long time for osseointegration while those implants have shown long-term clinical success in single and multiple restorations. Titanium implant surfaces have been modified in various ways to improve biocompatibility and accelerate osseointegration, which results in a shorter edentulous period for a patient. This article reviewed some important modified titanium surfaces, exploring the in vitro, in vivo and clinical results that numerous comparison studies reported. Several methods are widely used to modify the topography or chemistry of titanium surface, including blasting, acid etching, anodic oxidation, fluoride treatment, and calcium phosphate coating. Such modified surfaces demonstrate faster and stronger osseointegration than the turned commercially pure titanium surface. However, there have been many studies finding no significant differences in in vivo bone responses among the modified surfaces. Considering those in vivo results, physical properties like roughening by sandblasting and acid etching may be major contributors to favorable bone response in biological environments over chemical properties obtained from various modifications including fluoride treatment and calcium phosphate application. Recently, hydrophilic properties added to the roughened surfaces or some osteogenic peptides coated on the surfaces have shown higher biocompatibility and have induced faster osseointegration, compared to the existing modified surfaces. However, the long-term clinical studies about those innovative surfaces are still lacking.
PMCID: PMC4231373  PMID: 25400716
Anodic oxidation; BMP; fluoride; functional peptide; hydrophilicity; implant surface; SLA; surface modification.
12.  In Vitro and In Vivo Evaluation of Zinc-Modified Ca–Si-Based Ceramic Coating for Bone Implants 
PLoS ONE  2013;8(3):e57564.
The host response to calcium silicate ceramic coatings is not always favorable because of their high dissolution rates, leading to high pH within the surrounding physiological environment. Recently, a zinc-incorporated calcium silicate-based ceramic Ca2ZnSi2O7 coating, developed on a Ti-6Al-4V substrate using plasma-spray technology, was found to exhibit improved chemical stability and biocompatibility. This study aimed to investigate and compare the in vitro response of osteoblastic MC3T3-E1 cells cultured on Ca2ZnSi2O7 coating, CaSiO3 coating, and uncoated Ti-6Al-4V titanium control at cellular and molecular level. Our results showed Ca2ZnSi2O7 coating enhanced MC3T3-E1 cell attachment, proliferation, and differentiation compared to CaSiO3 coating and control. In addition, Ca2ZnSi2O7 coating increased mRNA levels of osteoblast-related genes (alkaline phosphatase, procollagen α1(I), osteocalcin), insulin-like growth factor-I (IGF-I), and transforming growth factor-β1 (TGF-β1). The in vivo osteoconductive properties of Ca2ZnSi2O7 coating, compared to CaSiO3 coating and control, was investigated using a rabbit femur defect model. Histological and histomorphometrical analysis demonstrated new bone formation in direct contact with the Ca2ZnSi2O7 coating surface in absence of fibrous tissue and higher bone-implant contact rate (BIC) in the Ca2ZnSi2O7 coating group, indicating better biocompatibility and faster osseointegration than CaSiO3 coated and control implants. These results indicate Ca2ZnSi2O7 coated implants have applications in bone tissue regeneration, since they are biocompatible and able to osseointegrate with host bone.
PMCID: PMC3590211  PMID: 23483914
13.  The pathway to intelligent implants: osteoblast response to nano silicon-doped hydroxyapatite patterning 
Bioactive hydroxyapatite (HA) with addition of silicon (Si) in the crystal structure (silicon-doped hydroxyapatite (SiHA)) has become a highly attractive alternative to conventional HA in bone replacement owing to the significant improvement in the in vivo bioactivity and osteoconductivity. Nanometre-scaled SiHA (nanoSiHA), which closely resembles the size of bone mineral, has been synthesized in this study. Thus, the silicon addition provides an extra chemical cue to stimulate and enhance bone formation for new generation coatings, and the next stage in metallic implantation design is to further improve cellular adhesion and proliferation by control of cell alignment. Topography has been found to provide a powerful set of signals for cells and form contact guidance. Using the recently developed novel technique of template-assisted electrohydrodynamic atomization (TAEA), patterns of pillars and tracks of various dimensions of nanoSiHA were achieved. Modifying the parameters of TAEA, the resolution of pattern structures was controlled, enabling the topography of a substrate to be modified accordingly. Spray time, flow rate and distance between the needle and substrate were varied to improve the pattern formation of pillars and tracks. The 15 min deposition time provided the most consistent patterned topography with a distance of 50 mm and flow rate of 4 µl min−1. A titanium substrate was patterned with pillars and tracks of varying widths, line lengths and distances under the optimized TAEA processing condition. A fast bone-like apatite formation rate was found on nanoSiHA after immersion in simulated body fluid, thus demonstrating its high in vitro bioactivity. Primary human osteoblast (HOB) cells responded to SiHA patterns by stretching of the filopodia between track and pillar, attaching to the apex of the pillar pattern and stretching between two. HOB cells responded to the track pattern by elongating along and between the track, and the length of HOB cells was proportional to the gaps between track patterns, but this relationship was not observed on the pillar patterns. The study has therefore provided an insight for future design of next generation implant surfaces to control and guide cellular responses, while TAEA patterning provides a controllable technique to provide topography to medical implants.
PMCID: PMC3061100  PMID: 21208969
patterning; electrohydrodynamic atomization; surface topography
14.  The Otto Aufranc Award: Demineralized Bone Matrix Around Porous Implants Promotes Rapid Gap Healing and Bone Ingrowth 
Noncemented revision arthroplasty is often complicated by the presence of bone implant gaps that reduce initial stability and biologic fixation. Demineralized bone matrix has osteoinductive properties and therefore the potential to enhance gap healing and porous implant fixation.
We determined at what times and to what extent demineralized bone matrix promotes gap healing and bone ingrowth around a porous implant.
We inserted porous titanium implants into the proximal metaphyses of canine femora and humeri, with an initial 3-mm gap between host cancellous bone and implants. We left the gaps empty (control; n = 12) or filled them with either demineralized bone matrix (n = 6) or devitalized demineralized bone matrix (negative control; n = 6) and left them in situ for 4 or 12 weeks. We quantified volume healing of the gap with new bone using three-dimensional micro-CT scanning and quantified apposition and ingrowth using backscattered scanning electron microscopy.
The density of bone inside gaps filled with demineralized bone matrix reached 64% and 93% of surrounding bone density by 4 and 12 weeks, respectively. Compared with empty controls and negative controls at 4 and 12 weeks, gap healing using demineralized bone matrix was two to three times greater and bone ingrowth and apposition were up to 15 times greater.
Demineralized bone matrix promotes rapid bone ingrowth and gap healing around porous implants.
Clinical Relevance
Demineralized bone matrix has potential for enhancing implant fixation in revision arthroplasty.
PMCID: PMC3254744  PMID: 21863397
15.  Strain driven fast osseointegration of implants 
Although the bone's capability of dental implant osseointegration has clinically been utilised as early as in the Gallo-Roman population, the specific mechanisms for the emergence and maintenance of peri-implant bone under functional load have not been identified. Here we show that under immediate loading of specially designed dental implants with masticatory loads, osseointegration is rapidly achieved.
We examined the bone reaction around non- and immediately loaded dental implants inserted in the mandible of mature minipigs during the presently assumed time for osseointegration. We used threaded conical titanium implants containing a titanium2+ oxide surface, allowing direct bone contact after insertion. The external geometry was designed according to finite element analysis: the calculation showed that physiological amplitudes of strain (500–3,000 ustrain) generated through mastication were homogenously distributed in peri-implant bone. The strain-energy density (SED) rate under assessment of a 1 Hz loading cycle was 150 Jm-3 s-1, peak dislocations were lower then nm.
Bone was in direct contact to the implant surface (bone/implant contact rate 90%) from day one of implant insertion, as quantified by undecalcified histological sections. This effect was substantiated by ultrastructural analysis of intimate osteoblast attachment and mature collagen mineralisation at the titanium surface. We detected no loss in the intimate bone/implant bond during the experimental period of either control or experimental animals, indicating that immediate load had no adverse effect on bone structure in peri-implant bone.
In terms of clinical relevance, the load related bone reaction at the implant interface may in combination with substrate effects be responsible for an immediate osseointegration state.
PMCID: PMC1277014  PMID: 16270927
16.  Porous Surface Modified Bioactive Bone Cement for Enhanced Bone Bonding 
PLoS ONE  2012;7(8):e42525.
Polymethylmethacrylate bone cement cannot provide an adhesive chemical bonding to form a stable cement-bone interface. Bioactive bone cements show bone bonding ability, but their clinical application is limited because bone resorption is observed after implantation. Porous polymethylmethacrylate can be achieved with the addition of carboxymethylcellulose, alginate and gelatin microparticles to promote bone ingrowth, but the mechanical properties are too low to be used in orthopedic applications. Bone ingrowth into cement could decrease the possibility of bone resorption and promote the formation of a stable interface. However, scarce literature is reported on bioactive bone cements that allow bone ingrowth. In this paper, we reported a porous surface modified bioactive bone cement with desired mechanical properties, which could allow for bone ingrowth.
Materials and Methods
The porous surface modified bioactive bone cement was evaluated to determine its handling characteristics, mechanical properties and behavior in a simulated body fluid. The in vitro cellular responses of the samples were also investigated in terms of cell attachment, proliferation, and osteoblastic differentiation. Furthermore, bone ingrowth was examined in a rabbit femoral condyle defect model by using micro-CT imaging and histological analysis. The strength of the implant–bone interface was also investigated by push-out tests.
The modified bone cement with a low content of bioactive fillers resulted in proper handling characteristics and adequate mechanical properties, but slightly affected its bioactivity. Moreover, the degree of attachment, proliferation and osteogenic differentiation of preosteoblast cells was also increased. The results of the push-out test revealed that higher interfacial bonding strength was achieved with the modified bone cement because of the formation of the apatite layer and the osseointegration after implantation in the bony defect.
Our findings suggested a new bioactive bone cement for prosthetic fixation in total joint replacement.
PMCID: PMC3414445  PMID: 22905143
17.  Total disc replacement arthroplasty using the AcroFlex lumbar disc: a non-human primate model 
European Spine Journal  2002;11(Suppl 2):S115-S123.
Using a non-human primate model, the current study was undertaken to investigate the efficacy of the AcroFlex lumbar disc as an intervertebral disc prosthesis, based on biomechanical, histopathologic and histomorphometric analyses. A total of 20 mature male baboons (Papio cynocephalus, mean weight 30 kg) were randomized into two equal groups based on post-operative time periods of 6 (n=10) and 12 months (n=10). Each animal underwent an anterior transperitoneal surgical approach to the lumbar spine, with intervertebral reconstructions performed at L3-L4 and L5-L6 using the following techniques: (1) tricortical iliac autograft and (2) AcroFlex lumbar disc. The two treatments were equally randomized between the non-contiguous operative lumbar levels. Post-mortem analysis included histopathologic assessment of the systemic reticuloendothelial tissues, multi-directional flexibility testing of the operative functional spinal units and quantitative histological analysis of trabecular bone coverage at the prosthesis endplates. Data were statistically compared using a one-way ANOVA with the Student-Newman-Keuls test. All animals survived the operative procedure and post-operative interval without significant intra- or peri-operative complications. Histopathologic analysis of the paraffin-embedded systemic reticuloendothelial tissues indicated no significant pathologic changes at the 6- or 12-month intervals. Plain film radiographic analysis showed no lucencies or loosening of any prosthetic vertebral endplate. Biomechanical testing of the 6-month autograft, reconstructions with AcroFlex lumbar disc and non-operative control (n=10) intact motion segments indicated no significant differences in peak range of motion (ROM) in axial compression. However, axial rotation produced significantly lower ROM for the autograft treatment compared to the intact and AcroFlex groups (P<0.05). The most significant differences in peak ROM were noted between all treatment groups under flexion/extension and lateral bending loading modalities (P<0.05). By 12 months, the intact condition indicated significantly more motion in all bending modes compared to the AcroFlex and autograft treatments, which were not statistically different from each other (P>0.05). Gross histopathologic analysis of the AcroFlex disc prosthesis demonstrated excellent ingrowth at the level of the implant-bone interface, without evidence of fibrous tissue or synovium. BioQuant histomorphometric analysis at the metal-bone interface (bone contact area/total endplate area) indicated the mean ingrowth was 54.59±13.24% at 6 months and 56.79±5.85% at 12 months. Radiographic analysis showed no lucencies or loosening of the AcroFlex vertebral endplate. Based on multi-directional flexibility testing, motion was preserved in axial rotation, but significantly diminished in the other bending modalities, particularly at the 12-month interval. This effect may be secondary to the limited surface area of device-vertebral endplate contact. Histomorphometric analysis of porous ingrowth coverage at the vertebral bone-metal interface was more favorable for total disc arthroplasty compared to historical reports of cementless femoral components. This project serves as the first comprehensive in vivo investigation into the AcroFlex disc prosthesis, and establishes an excellent research model in the evaluation of total disc replacement arthroplasty.
PMCID: PMC3611574  PMID: 12384732
Total disc replacement arthroplasty Animal model Biomechanics Histomorphometry Porous ingrowth
18.  Effect of cleaning and sterilization on titanium implant surface properties and cellular response 
Acta biomaterialia  2011;8(5):1966-1975.
Titanium (Ti) has been widely used as an implant material due to the excellent biocompatibility and corrosion resistance of its oxide surface. Biomaterials must be sterile before implantation, but the effects of sterilization on their surface properties have been less well studied. The effects of cleaning and sterilization on surface characteristics were bio-determined using contaminated and pure Ti substrata first manufactured to present two different surface structures: pretreated titanium (PT, Ra = 0.4 μm) (i.e. surfaces that were not modified by sandblasting and/or acid etching); (SLA, Ra = 3.4 μm). Previously cultured cells and associated extracellular matrix were removed from all bio-contaminated specimens by cleaning in a sonicator bath with a sequential acetone–isopropanol–ethanol–distilled water protocol. Cleaned specimens were sterilized with autoclave, gamma irradiation, oxygen plasma, or ultraviolet light. X-ray photoelectron spectroscopy (XPS), contact angle measurements, profilometry, and scanning electron microscopy were used to examine surface chemical components, hydrophilicity, roughness, and morphology, respectively. Small organic molecules present on contaminated Ti surfaces were removed with cleaning. XPS analysis confirmed that surface chemistry was altered by both cleaning and sterilization. Cleaning and sterilization affected hydrophobicity and roughness. These modified surface properties affected osteogenic differentiation of human MG63 osteoblast-like cells. Specifically, autoclaved SLA surfaces lost the characteristic increase in osteoblast differentiation seen on starting SLA surfaces, which was correlated with altered surface wettability and roughness. These data indicated that recleaned and resterilized Ti implant surfaces cannot be considered the same as the first surfaces in terms of surface properties and cell responses. Therefore, the reuse of Ti implants after resterilization may not result in the same tissue responses as found with never-before-implanted specimens.
PMCID: PMC3618465  PMID: 22154860
Titanium; Sterilization; Roughness; Hydrophilicity; MG63 cells
19.  Greater osteoblast and endothelial cell adhesion on nanostructured polyethylene and titanium 
Mostly due to desirable mechanical properties (such as high durability and low wear), certain synthetic polymers (such as polyethylene) and metals (such as titanium) have found numerous applications in the medical device arena from orthopedics to the vasculature, yet frequently, they do not proactively encourage desirable cell responses. In an effort to improve the efficacy of such traditional materials for various implant applications, this study used electron beam evaporation to create nanostructured surface features that mimic those of natural tissue on polyethylene and titanium. For other materials, it has been shown that the creation of nanorough surfaces increases surface energy leading to greater select protein (such as vitronectin and fibronectin) interactions to increase specific cell adhesion. Here, osteoblast (bone forming cells) and endothelial cell (cells that line the vasculature) adhesion was determined on nanostructured compared to conventional, nano-smooth polyethylene and titanium. Results demonstrated that nanorough surfaces created by electron beam evaporation increased the adhesion of both cells markedly better than conventional smooth surfaces. In summary, this study provided evidence that electron beam evaporation can modify implant surfaces (specifically, polyethylene and titanium) to have nanostructured surface features to improve osteoblast and endothelial cell adhesion. Since the adhesion of anchorage dependent cells (such as osteoblasts and endothelial cells) is a prerequisite for their long-term functions, this study suggests that electron beam evaporation should be further studied for improving materials for various biomedical applications.
PMCID: PMC2939710  PMID: 20856840
nanotechnology; polyethylene; osteoblasts; orthopedics; vascular; titanium
20.  Bone Response to Surface-Modified Titanium Implants: Studies on the Early Tissue Response to Implants with Different Surface Characteristics 
In a series of experimental studies, the bone formation around systematically modified titanium implants is analyzed. In the present study, three different surface modifications were prepared and evaluated. Glow-discharge cleaning and oxidizing resulted in a highly stoichiometric TiO2 surface, while a glow-discharge treatment in nitrogen gas resulted in implants with essentially a surface of titanium nitride, covered with a very thin titanium oxide. Finally, hydrogen peroxide treatment of implants resulted in an almost stoichiometric TiO2, rich in hydroxyl groups on the surface. Machined commercially pure titanium implants served as controls. Scanning Auger Electron Spectroscopy, Scanning Electron Microscopy, and Atomic Force Microscopy revealed no significant differences in oxide thickness or surface roughness parameters, but differences in the surface chemical composition and apparent topography were observed. After surface preparation, the implants were inserted in cortical bone of rabbits and evaluated after 1, 3, and 6 weeks. Light microscopic evaluation of the tissue response showed that all implants were in contact with bone and had a large proportion of newly formed bone within the threads after 6 weeks. There were no morphological differences between the four groups. Our study shows that a high degree of bone contact and bone formation can be achieved with titanium implants of different surface composition and topography.
PMCID: PMC3794548  PMID: 24174936
21.  Porous Tantalum Coatings Prepared by Vacuum Plasma Spraying Enhance BMSCs Osteogenic Differentiation and Bone Regeneration In Vitro and In Vivo 
PLoS ONE  2013;8(6):e66263.
Tantalum, as a potential metallic implant biomaterial, is attracting more and more attention because of its excellent anticorrosion and biocompatibility. However, its significantly high elastic modulus and large mechanical incompatibility with bone tissue make it unsuitable for load-bearing implants. In this study, porous tantalum coatings were first successfully fabricated on titanium substrates by vacuum plasma spraying (VPS), which would exert the excellent biocompatibility of tantalum and alleviate the elastic modulus of tantalum for bone tissue. We evaluated cytocompatibility and osteogenesis activity of the porous tantalum coatings using human bone marrow stromal cells (hBMSCs) and its ability to repair rabbit femur bone defects. The morphology and actin cytoskeletons of hBMSCs were observed via electron microscopy and confocal, and the cell viability, proliferation and osteogenic differentiation potential of hBMSCs were examined quantitatively by PrestoBlue assay, Ki67 immunofluorescence assay, real-time PCR technology and ALP staining. For in vivo detection, the repaired femur were evaluated by histomorphology and double fluorescence labeling 3 months postoperation. Porous tantalum coating surfaces promoted hBMSCs adhesion, proliferation, osteogenesis activity and had better osseointegration and faster new bone formation rate than titanium coating control. Our observation suggested that the porous tantalum coatings had good biocompatibility and could enhance osseoinductivity in vitro and promote new bone formation in vivo. The porous tantalum coatings prepared by VPS is a promising strategy for bone regeneration.
PMCID: PMC3679049  PMID: 23776648
22.  Osseointegration of porous titanium implants with and without electrochemically deposited DCPD coating in an ovine model 
Uncemented fixation of components in joint arthroplasty is achieved primarily through de novo bone formation at the bone-implant interface and establishment of a biological and mechanical interlock. In order to enhance bone-implant integration osteoconductive coatings and the methods of application thereof are continuously being developed and applied to highly porous and roughened implant substrates. In this study the effects of an electrochemically-deposited dicalcium phosphate dihydrate (DCPD) coating of a porous substrate on implant osseointegration was assessed using a standard uncemented implant fixation model in sheep.
Plasma sprayed titanium implants with and without a DCPD coating were inserted into defects drilled into the cancellous and cortical sites of the femur and tibia. Cancellous implants were inserted in a press-fit scenario whilst cortical implants were inserted in a line-to-line fit. Specimens were retrieved at 1, 2, 4, 8 and 12 weeks postoperatively. Interfacial shear-strength of the cortical sites was assessed using a push-out test, whilst bone ingrowth, ongrowth and remodelling were investigated using histologic and histomorphometric endpoints.
DCPD coating significantly improved cancellous bone ingrowth at 4 weeks but had no significant effect on mechanical stability in cortical bone up to 12 weeks postoperatively. Whilst a significant reduction in cancellous bone ongrowth was observed from 4 to 12 weeks for the DCPD coating, no other statistically significant differences in ongrowth or ingrowth in either the cancellous or cortical sites were observed between TiPS and DCPD groups.
The application of a DCPD coating to porous titanium substrates may improve the extent of cancellous bone ingrowth in the early postoperative phase following uncemented arthroplasty.
PMCID: PMC3223135  PMID: 22053991
Bone ingrowth; Interfacial shear strength; Calcium phosphate; Osteoconduction; Bone remodeling
23.  The role of biocompatible coatings of biomaterials for creation of direct and appropriate chemical bounding between bioimplant and bone tissue 
Journal of Injury and Violence Research  2012;4(3 Suppl 1): Paper No. 39.
Nowadays, the surface modification of biomaterials to increase biocompatibility and improve other aspects of environmental performance is widely prevalent and is developing. Biological host response depends on the primary interactions of biological and biomaterials systems at the molecular surfaces. Therefore, the surface properties at the atomic scale influence on compatibility and optimal performance of the material in body. The present study aims to survey the most common surface modification techniques of biomaterials focusing on the surface coating techniques and their applications in bone tissue engineering and tissue repairing field. Furthermore, the process and features of biomaterial surface coating in complex superficial modification of biomaterials as a representation of biomaterials interfaces with the biological environment are discussed. Finally, the potential applications and advantages of these techniques in repairing damaged tissues in neurosurgery and orthopedic surgery are presented.
In this review article, the most common and important methods of surface modification of biomaterials (thermal spray, electrophoresis, pulsed laser deposition, electrochemical, biomimetic, sputtering, Chemical Vapor Deposition (CVD), and, Sol–Gel techniques) which the reputable manufacture companies of biomaterial are applying and many published articles in the biomaterial field (since 2004 up to now). Furthermore, the potential applications and current positions of these methods in bone tissue engineering and effective factors for an optimal tissue repairing using biomaterial surface coating are presented.
The Sol-gel method is suitable for obtaining nanoscale structures. Plasma spraying method has a high-speed balance and is the only commercially available method. The pulsed laser coating method can be used in multilayer coatings and structures with a fixed Stoichiometric.
The electrophoresis coating methods are able to coat relatively complex shapes with precise control over coating thickness.In recent years, several coating methods such as electrochemical, biomimetic, sputtering, and CVD have been proposed and used by researchers some of them with good satisfactory results.
Findings of our survey show that surface modification of biomaterials can keep the crucial physical properties of the biomaterials unchanged which is an important feature in biological reactions. The main advantages of biomaterial surface modification including surface coating can be presented as follows:
Reducing protein adsorption:Biomaterials sometimes need to have the lowest protein adsorption, otherwise, will cause uncontrolled immune responses.
Lack of cellular coherency
Cellular absorption:Biomaterials that are used as replacement tissue cells must have high capability for cell absorption and also should facilitate their growth process.
Reducing Clot formation:Biomaterials that are used as blood implants should have the lowest capacity of clot formation.
High coherency to bacteria
Reducing friction and grinding
Biomaterials, Coating, Biocompatibility, Grinding, Bounding, Implant
PMCID: PMC3571565
24.  Nanostructured model implants for in vivo studies: influence of well-defined nanotopography on de novo bone formation on titanium implants 
An implantable model system was developed to investigate the effects of nanoscale surface properties on the osseointegration of titanium implants in rat tibia. Topographical nanostructures with a well-defined shape (semispherical protrusions) and variable size (60 nm, 120 nm and 220 nm) were produced by colloidal lithography on the machined implants. Furthermore, the implants were sputter-coated with titanium to ensure a uniform surface chemical composition. The histological evaluation of bone around the implants at 7 days and 28 days after implantation was performed on the ground sections using optical and scanning electron microscopy. Differences between groups were found mainly in the new bone formation process in the endosteal and marrow bone compartments after 28 days of implantation. Implant surfaces with 60 nm features demonstrated significantly higher bone-implant contact (BIC, 76%) compared with the 120 nm (45%) and control (57%) surfaces. This effect was correlated to the higher density and curvature of the 60 nm protrusions. Within the developed model system, nanoscale protrusions could be applied and systematically varied in size in the presence of microscale background roughness on complex screw-shaped implants. Moreover, the model can be adapted for the systematic variation of surface nanofeature density and chemistry, which opens up new possibilities for in vivo studies of various nanoscale surface-bone interactions.
PMCID: PMC3260035  PMID: 22267926
in vivo; nanotopography; osseointegration; titanium implant; colloidal lithography
25.  Does Using Autograft Bone Chips Achieve Consistent Bone Ingrowth in Primary TKA? 
Cementless fixation remains controversial in TKA due to the challenge of achieving consistent skeletal attachment. Factors predicting durable fixation are not clearly understood, but we presumed bone ingrowth could be enhanced by the quantity of host bone and application of autograft bone chips.
We asked: (1) Did the amount of bone ingrowth exceed the amount of periprosthetic and host bone with the addition of autograft bone chips? (2) Did the amount of bone ingrowth increase with implantation time? And (3) did osteolysis along the porous-coated interface and screw tracts progress with implantation time?
We measured the amount of bone in the porous-coated, periprosthetic, and host bone regions in 19 postmortem retrieved cementless primary total knee implants. The amount of bone in apposition to the implant surface, and alternatively lysed bone, was analyzed radiographically to assess the progression of osteolysis.
While bone ingrowth tended to be less than periprosthetic and host bone in all three components, it was only significantly less in the patellar component. Bone ingrowth increased in all three components over time, but progression of osteolysis did not.
Even after long-term followup, the amount of bone ingrowth did not surpass host bone levels, suggesting the amount of a patient’s host bone is a limiting factor in the amount of bone ingrowth achievable for this cementless design. It remains unknown whether compromised osteopenic bone could achieve the amount of bone attachment necessary to provide durable fixation over time.
Level of Evidence
Level IV, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.
PMCID: PMC3369085  PMID: 22179980

Results 1-25 (1129093)