|Home | About | Journals | Submit | Contact Us | Français|
Laser ablation of selected coordination complexes can lead to the production of metal-carbon hybrid materials, whose composition and structure can be tailored by suitably choosing the chemical composition of the irradiated targets. This ‘laser chemistry’ approach, initially applied by our group to the synthesis of P-containing nanostructured carbon foams (NCFs) from triphenylphosphine-based Au and Cu compounds, is broadened in this study to the production of other metal-NCFs and P-free NCFs. Thus, our results show that P-free coordination compounds and commercial organic precursors can act as efficient carbon source for the growth of NCFs. Physicochemical characterization reveals that NCFs are low-density mesoporous materials with relatively low specific surface areas and thermally stable in air up to around 600°C. Moreover, NCFs disperse well in a variety of solvents and can be successfully chemically processed to enable their handling and provide NCF-containing biocomposite fibers by a wet-chemical spinning process. These promising results may open new and interesting avenues toward the use of NCFs for technological applications.
Laser technologies can be successfully utilized for the production of carbon-nanostructured materials exhibiting fascinating structural and physical properties such as carbon nanotubes , carbon nanohorns , carbon nanofoams , or shell-shaped carbon nanoparticles . Our group discovered the production of metal-nanostructured foams (NCFs) by laser ablation of triphenylphosphine (PPh3)-containing organometallic targets . We then demonstrated that organic ligands can act as efficient carbon sources for the laser ablation production of carbon nanomaterials. Metal-NCFs are three-component materials which consist of amorphous carbon aggregates, metal nanoparticles embedded in amorphous carbon matrices, and graphitic nanostructures. The metal-NCF composition, metal nanoparticle size, and dilution (i.e., metal and carbon content) within the carbon matrices can be tailored by conveniently choosing the metals (Au, Cu) and ligands of the ablated targets . On the other hand, laser ablation of PPh3 resulted in the production of metal-free NCFs consisting of graphitic nanostructures and P-containing amorphous carbon aggregates . We report how our versatile ‘laser chemistry’ approach can be extended to the synthesis of a variety of other metal-NCFs, as well as to metal-free, P-free NCFs, proving that the synthesis of NCFs is not restricted to PPh3-based targets and therefore enabling envisioning the synthesis of metal-carbon hybrids by chemical design. Additionally, physicochemical studies have been performed on metal-free NCFs to evaluate their potential applications. We also show that NCFs can be easily chemically processed in the form of stable NCF dispersions in different solvents and NCF biocomposite fibers, which offer promise for NCF incorporation into different matrices and technological applications.
The production of carbon foams has been carried out by Nd:YAG laser ablation of thick layers of coordination and organic compounds in air atmosphere using the setup described in Figure 1 and under the experimental conditions described elsewhere [5,6]. Different metal-NCFs have been produced by laser irradiation of dichlorobis(triphenylphosphine)nickel(II) [NiCl2(PPh3)2], dichlorobis(triphenylphosphine)cobalt(II) [CoCl2(PPh3)2], and [1,2-bis(diphenylphosphino)ethane]dichloroiron(II) [FeCl2(Dppe)]. P-free metal-NCFs were produced using bis(benzonitrile)dichloropalladium(II) [PdCl2(PhCN)2], dichloro(1,10-phenanthroline)palladium(II) [PdCl2(Phen)], and (2,2´-bipyridine)dichloropalladium(II) [PdCl2(Bipy)]. Naphthalene, phenanthrene, and 1,10-phenanthroline have been used as precursors for the synthesis of metal-free, P-free NCFs. All chemicals were purchased from Sigma-Aldrich (Schnelldorf, Germany and Saint-Quentin-Fallavier, France) and used as received.
The structure of the synthesized NCFs was imaged by scanning electron microscopy (SEM, Hitachi S-3400N (Hitachi, Ltd., Chiyoda-ku, Japan), including a Röntec XFlash detector (Röntec GmbH, Berlin, Germany) for energy dispersive X-ray spectroscopy (EDS) analyses), and transmission electron microscopy (TEM, JEOL JEM-3000F microscope, JEOL Ltd., Akishima-shi, Japan, equipped with an Oxford Instruments ISIS 300 X-ray microanalysis system and a Link Pentafet detector, Oxford Instruments, Abingdon, UK, for EDS analyses). NCF thermal stability in air was studied by thermogravimetric analysis (TGA, SETARAM Setsys Evolution, Hillsborough, NJ, USA; samples were analyzed in Pt pans at a heating rate of 10°C/min up to 850°C in an atmosphere of air flowing at 100 mL/min). Micro-Raman spectroscopy studies were carried out using a Dilor XY Raman spectrometer (λexc = 514.5 nm, HORIBA, Ltd., Kyoto, Japan). Elemental analyses of metal-free NCFs were performed using a Thermo Flash EA 1112 Series NC analyzer (Thermo Fisher Scientific, Waltham, MA, USA). The textural properties of NCFs were studied using nitrogen adsorption-desorption isotherms measured at 77 K (Micromeritics ASAP 2020, Norcross, GA, USA) and using the Brunauer-Emmett-Teller (BET) method between 0.05 and 0.3 P/P0 and t-Plot and Barret-Joyner-Halenda (BJH) method. Density values were measured using an AccuPyc II 1340 Micromeritics helium picnometer (Micromeritics, Norcross, GA, USA).
Fiber spinning of NCF biocomposites was performed by injecting 1:4 Au-NCF:sodium alginate (MW: 400K) aqueous dispersions (1 mg/mL Au-NCF prepared by bath sonication) into a coagulation bath (5% CaCl2 solution in 70% methanol) following the carbon nanotube biofiber spinning procedure reported by Razal et al. . The electrical conductivity of the spun fibers was characterized by four-probe resistance measurements using a Keithley 2000 Multimeter (Keithley Instruments, Inc., Cleveland, OH, USA).
SEM (Figure 2), TEM (Figure 3), and EDX characterization of the soot that resulted from the laser irradiation of different organometallic targets show that our laser ablation technique is not only restricted to the synthesis of Au/NCFs and Cu/NCFs [5,6], but it can also provide a new family of metal-NCF hybrids of any desired metal. These metal-NCFs exhibit a spongy-like microstructure (Figure 2a) as a result of nanoparticle assembly. These nanoparticles consist of amorphous carbon particles, graphitic nanostructures, and metal nanoparticle-containing amorphous carbon aggregates (Figure 3a,b,c). Moreover, metal-NCFs that result from the laser irradiation of [PdCl2(PhCN)2], [PdCl2(Phen)], and [PdCl2(Bipy)] also indicate that aromatic ligands different than PPh3 and without phosphor in their composition, such as benzonitrile, 1,10-phenanthroline, or 2,2´-bipyridine, can also efficiently act as carbon source for the laser production of carbon matrices (Figures 2 and and33).
Based on these findings, we then irradiated different aromatic compounds toward the synthesis of metal-free and P-free NCFs. Thus, laser ablation of naphthalene, phenanthrene, and 1,10-phenanthroline resulted in the formation of a NCF material which consisted of both amorphous carbon aggregates and graphitic nanodomains (Figures 2b and and3d).3d). Elemental analysis data reveal high carbon contents (≥95%) for these metal-free NCFs. The extensive charging observed in NCFs without any conductive coating deposited on conducting carbon films for SEM characterization reveals the nonconducting nature of these materials. The Raman spectra of the metal-free NCFs show broad D- and G-bands of comparable intensities, a feature typical of short-range sp2-bonded carbons [6,8]. As an example, we show in Figure 4 the spectrum of NCFs produced by laser ablation of naphthalene. The much broader aspect of the D-band (as compared to the G-band) indicates that this material lacks long-range graphitic order. According to Ferrari's model of graphite amorphization path , this material would be in stage 2 of amorphization (denoted as sp2 a-C in ) in which only some sp2-bonded rings remain, thus confirming the predominance of amorphous carbon already observed by TEM.
TGA analyses show that metal-free NCFs are thermally stable in air up to temperatures of approximately 600°C. It is interesting to point out that the temperature of maximum decomposition rate of NCFs produced by laser ablation of PPh3 (which contains 8.2% P) is about 30°C higher than that of the naphthalene-produced NCFs, probably as a result of flame retardant role of P . The study of the textural properties reveals that NCFs produced by laser ablation of PPh3 and naphthalene are mesoporous materials with BET surface areas between 33 and 63 m2/g and mesopore volumes of 0.046 to 0.168 cm3/g, respectively. The measured BET surface area values are lower than those of other carbon materials consisting of amorphous carbon aggregates such as carbon aerogels (typical values in the range 400 to 600 m2/g) [10,11] and carbon nanofoams (300 to 400 m2/g) produced by femtosecond pulsed laser ablation of HOPG . Additionally, density values of 1.66 g/cm3 have been measured for naphthalene-produced NCFs by He picnometry. These values are similar to those of other carbon materials (Table 1) such as multi-walled carbon nanotubes, carbon xerogels, carbon black, graphitic cones, and ordered mesoporous carbon but significantly higher than those reported for carbon nanofoams produced by ultrafast lasers (0.02 to 0.002 g/cm3) .
NCFs are collected from laser ablation processes as intractable soots. In order to evaluate the potential chemical processing capabilities of our NCFs, these materials were dispersed in different solvents. Mild (bath) sonication resulted in NCF dispersions which are stable for over 48 h in all tested solvents but in hexane (Figure 5). This NCF remarkable dispersibility opens new opportunities toward the incorporation of these nanocarbons into functional materials and assemblies. Thus, Au-NCF/alginate biocomposite fibers, tens of centimeters in length and 30 to 50 micrometers in diameter (Figure 6), were spun by coagulation of sodium alginate assisted Au-NCF aqueous dispersions in a CaCl2 water/methanol solution, followed by RT drying in air of the resulting elastomeric gels. Four-probe resistance measurements revealed that these fibers were nonconducting. This fiber spinning method is an interesting strategy for easy NCF handling and for providing a confinement in the form of quasi 1D architectures to metal nanoparticles.
The laser chemistry approach described in the present work is a versatile method for the synthesis of metal nanoparticles embedded in carbon matrices from molecular precursors. This laser chemistry is very appealing for applications requiring metal nanoparticles largely isolated from each other embedded in solid matrices. Moreover, it can be used for the synthesis of metal-free, P-free NCFs from commercial organic precursors, which would in turn facilitate upscaling their production. On the other hand, the chemical processing capabilities of NCFs ease their handling and may open attractive opportunities toward their incorporation into matrices and applications. Future challenges should deal with the design of production or processing strategies to increase the surface area and conductivity of these materials to enable their use as, for example, electrode materials, in catalysis, or as functional magnetic materials.
The authors declare that they have no competing interests.
ASA, RL, GFF, and EM carried out the laser ablation experiments. EM, GFF, ML, and ASA conceived the study. MLS performed the Raman characterization. ASA carried out the electron microscopy and physicochemical characterization, and completed the data analysis. RG was in charge of further physicochemical studies and assisted in data analysis. JMR and EM performed the fiber spinning experiments. RG and EM drafted the manuscript. All authors read and approved the final manuscript.
This work has been supported by the regional Government of Aragón (Spain, Project PI119/09, and E101 and T87 Research Groups funding) and the Spanish Government and Feder funds through grant MAT2010-19837-C06-06. This work has been funded in part by the European Commission through projects LIFE11/ENV/ES 560 and grant agreement no. 280658. The authors would like to acknowledge the use of Servicio de Microscopia Electrónica (Servicios de Apoyo a la Investigación), Universidad de Zaragoza. The authors also thank the technical assistance provided by the Servicio de Análisis of the Instituto de Carboquímica ICB-CSIC. The authors thank María Jesús Lázaro for kindly providing carbon xerogel and ordered mesoporous carbon samples. Carbon black and activated carbon samples were kindly supplied by Delta Tecnic S.A. and Morgui Clima S.L, respectively.